MARINE DATASHEETS

All Marine Datasheets are listed below, alternatively click on the links to the left to filter your search:

• Ampreg 21 – Epoxy Wet Laminating System (v7)
  Ampreg 21 has been optimised for the manufacture of large composite structures using hand layup, and vacuum bagging techniques.
• Ampreg 21FR - Fire Retardant Epoxy Wet Laminating System (v6)
  Ampreg 21FR has been optimised for the manufacture of large composite structures using hand layup, and vacuum bagging techniques.
• Ampreg 22 - Epoxy Laminating System (v17)SP
  Ampreg 22 - Epoxy Laminating System is an established and widely used laminating system.
• Ampreg 26 - Epoxy Laminating System (v11)SP
  Ampreg 26 is SP’s premium epoxy laminating system, and is particularly suitable for the manufacture of large, high performance composite structures.
• Ampreg Adhesion Promoter - Resin System (v3)
  Ampreg Adhesion Promoter (AP) is a unique resin system formulated to promote the adhesion between epoxy and vinylester resin. This allows production boatbuilders to use existing polyester gelcoats with higher performance epoxy resins
• Ampreg F230-1 Foaming Epoxy System (v1)
  Three-part foaming epoxy system which uses Ampreg 21 hardeners. Foam expands approximately 4x by volume to create a foam of 220-250kg/m3.
• Ampreg Thixotropic Pregel - Resin Additive (v2)
  Ampreg Thixotropic Pregel is a resin additive with a grease-like consistency, which can be used with a variety of hardeners from the SP laminating resin range. It is used primarily as a thixotrope - to be added to low viscosity laminating resin
• Balsaflex® - Balsa Wood Core Material (v3) SP-HM
  Balsaflex® is a typical density balsa wood core material. When an application requires high strength, stiffness and cost effectiveness, Balsaflex® is a suitable solution due to a good balance between cost, properties and weight.
• Corecell™ A-Foam – Structural Core Material (v9)SP-HM
  Corecell™ A-Foam is the original Corecell material, developed because of frustrations with inadequate PVC core technology in marine sandwich structures. Corecell A-Foam is well known for it’s incredible toughness and resistance to cracking.
• Corecell™ M-Foam – The Marine Foam (v5)
  Corecell™ M-Foam has been developed to deliver one product for all Marine applications. It provides a unique combination of high shear strength with low density, high elongation, high temperature resistance and low resin uptake.
• Corecell™ P-Foam – Structural Core Material (v7)SP-HM
  Corecell™ P-Foam is a development of Corecell™ A-Foam, intended for prepreg and SPRINT® manufacturing processes.
• Corecell™ S-Foam – Structural Foam Core (v8)SP-HM
  Corecell™ S-Foam has been designed specifically for use in sub-sea buoyancy applications. Its resistance to crushing means that it can withstand depths of over 900m, and its closed-cell structure gives it a high water resistance.
• CR 3400 - In-Mould Epoxy Gelcoat/Surfacing System (v10) SP-HM
  CR 3400 is an in-mould epoxy surfacing system for epoxy laminates, and is designed to be used as the base for the subsequent application of a paint scheme.
• Eposeal 300 - Universal Epoxy Sealer (v9)
  Eposeal 300 is a solvent-based, low viscosity epoxy sealer. It has been developed primarily for use on wood but can also be used on other materials such as GRP, stone, ferrocement, brick, etc.
• G-PET - Recyclable Structural Foam (v1) SP-HM
  G-PET Recyclable structural foam is a highly adaptable, recyclable, thermoplastic core material with good balance of mechanical properties, temperature resistance, density and cost for a wide range of applications and processes.
• Handipack - Multi-purpose Epoxy System (v10)
  Handipack is a multi-purpose epoxy, supplied only in a small pack. It is designed for quick repair work and small scale construction jobs. Best suited to small tasks, and should not be applied in thicknesses exceeding 3mm.
• PRIME™ 20LV - Epoxy Infusion System (v9) SP-HM
  PRIME™ 20LV is the next generation of PRIME™ 20 epoxy infusion system, which is specifically designed for use in a variety of resin infusion processes
• PRIME™ 20ULV - Ultra Low Viscosity Epoxy Infusion System (v4)
  PRIME™ 20 ULV is a Ultra Low Viscosity Epoxy Infusion System with fast infusion times. It is Ideal for production boatbuilders, who want to combine the use of polyester gelcoats with epoxy backing laminates
• PRIME™ 27 Epoxy Infusion System (v3) SP-HM
  PRIME™ 27 is suitable for the female moulding of large, complex components incorporating advanced fibres such as carbon and aramid*. Typical projects include spars, hulls and reinforcing structures.
• PVCell® G-Foam - Structural Foam Core (v2) SP-HM
  PVCell® G-Foam is a closed cell, cross-linked PVC foam. It provides superior strength to weight ratio for all composite applications. PVCell® G-Foam is available in a wide range of formats with all standard cut patterns and finishes possible.
• SA 70 - Epoxy Adhesive System (v4)
  SA 70 adhesive film is a toughened epoxy film on a glass carrier with excellent tack and drape characteristics. It offers many advantages over traditional wet lay-up techniques for bonding of composite skins to cores.
• SA 80 - Toughened Epoxy Adhesive Film (v9)
  SA 80 adhesive film is a toughened epoxy film on a glass carrier with excellent tack and drape characteristics. It offers many advantages over traditional wet lay-up techniques for bonding of composite skins to cores.
• S-Core - SPRINT® Core Material (v4) SP-HM
  The S-Core, or SPRINT® core, is a moulding material that consists of a single layer of a polyester non woven material, that has a pressure stable honeycomb structure, applied to a precast, recatalysed resin film.
• SE 70 - Low Temp Cure/High Toughness (v5)
  SE 70 is a hot-melt, low temperature cure, epoxy prepreg system. It has been developed for use in the construction of large components using low energy cure cycles. Excellent properties can be achieved with a processing temperature of just 70°C.
• SE 84 Nano - High Performance Prepreg (v1)
  SE 84 Nano is a high performance hot-melt epoxy prepreg. When vacuum bag moulded SE 84 Nano exhibits a 20% increase in compressive strength compared to SE 84LV
• SE 84LV - Low Temp Epoxy Prepreg System (v12)
  Low Temperature Cure Epoxy Prepreg System, Versatile, high-strength prepreg system, Curable at temperatures as low as 80°C, Can be processed with vacuum-only processing, Excellent tack, Low viscosity - Ideal for use with heavy fibre weights can be used for faster moulding of components at 120°C.
• SE 85 - Epoxy Prepreg System (v9)
  The SE 85 series are toughened hot-melt, epoxy prepregs that offers an extremely good balance of mechanical properties. They are ideal for structural components where improved impact performance and resistance to resin microcracking is desired.
• SE 85GT - Epoxy Prepreg System (v2)
  The SE 85GT series are highly toughened hot-melt, epoxy prepregs that offer an extremely good balance of mechanical properties.
• SF 70 SPRINT® Toughened Surfacing Film (v2)
  SF 70 surfacing material is a light green toughened, epoxy film designed to enhance the surface finish of moulded composite components. It allows a good surface finish to be obtained by vacuum-bag moulding processes.
• SF 80 - SPRINT® Toughened Surfacing Film (v2)
  SF 80 surfacing material is a light green toughened, epoxy film designed to enhance the surface finish of moulded composite components. It allows a good surface finish to be obtained by vacuum-bag moulding processes.
• SF 80FB - Fire-Barrier Surfacing Film (v2)SP-HM
  SF 80FB surfacing material is a black, filled epoxy film containing a 320g intumescent layer. Typical applications include the protection of structural components in high risk areas such as engine bays, exhaust runs, and around the fuel system.
• SF 80FROBL - Fire-Retardant Surfacing Film (v2) SP
  SF 80FROBL surfacing material is a black, filled epoxy film. It provides an effective fire retarding layer capable of withstanding exposure to fire, while preventing the epoxy substrate from combustion.
• SF 95PF - Sandable Surfacing Film (v2) SP-HM
  The SF 95PF surfacing material is a grey filled epoxy film designed to enhance the surface finish of moulded composite components. It allows a good surface finish to be obtained by vacuum-bag moulding processes.
• SP 106 - Multi-purpose Epoxy System (v11)
  SP 106 is a simple to use, all-purpose epoxy which can be used for gluing, coating, laminating and filling. SP 106 provides a quick and convenient way of using one epoxy system for a very wide range of tasks.
• SP 115 Clear Epoxy Laminating System (v7) SP-HM
  SP 115 is a low viscosity, ultra-clear epoxy laminating system. It has been designed for the manufacture of laminates such as those used in sail and surfboards which are to remain unpainted, and where a very clear finish is required.
• SP 320 - Solvent-Free Clear Epoxy Coating System (v7)
  SP 320 is a solvent-free, clear epoxy coating that provides a high clarity, tough finish to whatever it is applied to. The epoxy coating will protect most surfaces from moisture ingress, and will also add strength to softwood surfaces.
• SP 4202 - Mono-component Epoxy System (v4)
  SP 4202 is a single component epoxy system designed to co-cure at moderate elevated temperature with SP’s SE prepregs. The product is designed to be applied between gel coat and prepreg, and will bridge any large gaps between the two.
• SP 4832 - Mono-component Epoxy System (v2)
  SP 4832 is a highly thixotropic, gap filling paste. It is a single component epoxy system designed to co-cure at moderate elevated temperature with SE prepregs.
• Spabond 340LV - Epoxy Ahesive System (v13)SP
  Spabond 340 LV is a high performance adhesive designed for bonding large structures such as yacht hulls and wind turbine blades. It is a cost-effective system with good thermal and mechanical properties.
• Spabond 345 - Epoxy Adhesive System (v7)
  Spabond 345 is a toughened, high performance adhesive system ideal for bonding large structures where substrate surfaces have uneven geometry.
• Spabond 368 - Epoxy Adhesive System (v1)
  Spabond 368 is a low density adhesive, with a simple 2:1 by volume mix ratio which is designed for bonding a wide range of core materials.
• Spabond 370 - Epoxy Adhesive System (v3)
  Spabond 370 teak deck adhesive has been formulated to give the optimum mechanical and working properties for bonding teak decking to a composite hull. Designed specifically for this purpose, it is the ideal adhesive for bonding down teak decks.
• Spabond 540 - Modified Epoxy Adhesive (v3)
  Spabond 540 is a modified ambient curing epoxy adhesive designed for bonding polyester or epoxy laminates.
• Spabond 5-Minute - Epoxy Adhesive System (v7)
  Spabond 5-Minute uses SP’s fast-setting technology. It combines outstanding bonding speed with a simple 1:1 by weight and by volume mix ratio. This thixotropic system is ideal for general bonding and repair work on a wide range of materials.
• Spabond 730 - Rapid Structural Adhesive (v4)SP-HM
  Spabond 730 is a fast curing structural adhesive designed for applications where reduced clamp times are important. It has a simple 1:1 by weight and volume mix ratio.
• ST 70 - Carbon Structural SPRINT® (v2)
  ST70 is part of the range of SPRINT® products. This unique product range provides technically and commercially competitive engineering materials, ideal for use either solely, or in conjunction with other products from within the product range
• ST 70 - Glass Structural SPRINT® (v2)
  ST70 is part of the range of SPRINT® products. This unique product range provides technically and commercially competitive engineering materials, ideal for use either solely, or in conjunction with other products from within the product range
• ST 70FR - Fire Retardant Glass Structural SPRINT® (v9)
  ST70FR is a fire retardant hot melt, Diuron free epoxy SPRINT®. This is ideally suited to the manufacture of thick sections requiring fire protection.
• ST 90FR - Fire Retardant SPRINT® System SP (v2)
  ST 90FR is a fire-retardant, hot-melt, epoxy prepreg system that offers an extremely good balance of mechanical properties.
• ST 94 - Single SPRINT® (v4)SP-HM
  ST 94 Single SPRINT® is a moulding material that consists of a layer of dry reinforcement plied to a precast, precatalysed resin film. ST 94 is a toughened hot-melt, epoxy resin that offers an extremely good balance of mechanical properties.
• ST 95 - Carbon Structural SPRINT® (v4)SP-HM
  The patent-approved ST 95 Structural SPRINT® is a moulding material that consists of two layers of carbon reinforcement either side of a precast, precatalysed resin film.
• ST 95 - Glass Structural SPRINT® (v2)SP-HM
  The patent-approved ST 95 Structural SPRINT® is a moulding material that consists of two layers of glass reinforcement either side of a precast, precatalysed resin film.
• T-Lam 130-1 Slow - Epoxy Tooling Laminating System (v4)SP-HM
  T-Lam 130-1 Slow is an epoxy tooling system for manufacturing glass or carbon moulds by wet laminating.
• T-Paste 70-2 Low Density Epoxy Tooling Paste (v2)
  T-Paste 70-2 has been designed for Marine, Wind Energy and Automotive customers looking for a fast and reliable way to manufacture patterns and direct moulds.
• T-Prime 130-1 - Epoxy Tooling Infusion System (v2)SP-HM
  T-Prime 130-1 is an epoxy tooling system for manufacturing glass or carbon moulds from liquid infusion processes.