WIND ENERGY DATASHEETS

• Ampreg 21 - Epoxy Wet Laminating System (v7)WE
  Ampreg 21 has been optimised for the manufacture of large composite structures using hand layup, and vacuum bagging techniques.
• Ampreg 22 - Epoxy Laminating System (v17)
  Ampreg 22 is an established and widely used laminating system. It is intended for both wet lay-up and vacuum bagging processes and uses the most up-to-date epoxy chemistry available.
• Balsaflex® - Balsa Wood Core Material (v3)
  Balsaflex® is a typical density balsa wood core material. When an application requires high strength, stiffness and cost effectiveness, Balsaflex® is a suitable solution due to a good balance between cost, properties and weight.
• Corecell™ K-Foam – Structural Foam Core (v7)
  Corecell™ K-Foam is a development of Corecell™ T-Foam with higher temperature stability for processing under vacuum. It shares Corecell™ T-Foam’s exceptional balance of toughness and stiffness.
• Corecell™ T300 Structural Foam Core (v3)
  Corecell™ T300 is a structural Foam Core which is suitable for all PVC core applications. It has excellent mechanical properties with outstanding chemical resistance which is ideal for resin infusion
• Corecell™ T-Foam – Structural Foam Core (v8)
  Corecell™ T-Foam has been developed as a technological step-change from traditional PVC and Balsa structural core. It has slightly higher stiffness properties and even greater styrene resistance than the more ductile Corecell™ A-Foam. Supplied in following grades/densities: T400, T500, T550, T600, T800
• CR 3400 - In-Mould Epoxy Gelcoat/Surfacing System (v10)
  CR 3400 is an in-mould epoxy surfacing system for epoxy laminates, and is designed to be used as the base for the subsequent application of a paint scheme.
• G-PET - Recyclable Structural Foam (v7)
  Highly adaptable, recyclable, thermoplastic foam with good balance of mechanical properties, temperature resistance, density and cost for a wide range of applications and production processes.
• PRIME™ 20LV - Epoxy Infusion System (v7)
  PRIME™ 20LV has a much reduced viscosity resin and longer working time, which makes it ideal for infusing very large parts with complex reinforcements in one operation.
• PVCell® G-Foam - Structural Foam Core (v9)WE
  PVCell® G-Foam is a closed cell, crosslinked PVC foam.
• RENUVO™ Multi-purpose System (MPS) v4
  RENUVO™ Blade Repair System is a UV curing System for Turbine Blade repair. Fast curing single component resin developed to work even in low temperatures, saving time, effort and waste in all repair formats.
• RENUVO™ Prepreg (PP) v4
  RENUVO™ Blade Repair System is a UV curing biaxial Prepreg for Turbine Blade repair. Fast curing single component resin developed to work even in low temperatures, saving time, effort and waste in all repair formats.
• RENUVO™ Wet Laminating System (WL) v2
  RENUVO™ Wet Laminating System (WL), is a breakthrough UV curing resin system, developed by Gurit as a repair system for straight from the mould turbine blades.
• S'Fair 15 Minute Filler (v1)
  S-Fair 15 Minute Filler is an epoxy filler system designed for rapid cure at ambient temperature, to allow sanding without clogging at just over an hour after application.
• SP 110 Epoxy Laminating System (v7)
  SP 110 is a versatile high strength epoxy laminating system which is ideal for the manufacture or repair of lightweight, high strength composites, using glass, aramid or carbon fibres.
• SP9435 - Monocomponent Epoxy System (v7)
  SP 9435 is a single component epoxy system designed to co-cure at moderate elevated temperature with Gurit’s SE prepregs. The product is designed to be applied between gel coat and prepreg, and will bridge any large (up to 20mm) gaps between the two. It is a highly thixotropic, gap filling paste.
• Spabond 340 - Epoxy Adhesive System (v8)
  Spabond 340 is a toughened, thixotropic adhesive system with a simple 2:1 by weight and by volume mix ratio. It is designed for use with a mixing machine and has a sag resistance of 30mm on a vertical surface.
• Spabond 340LV - Epoxy Adhesive System (v13)
  Spabond 340LV is a high performance adhesive designed for bonding large structures such as yacht hulls and wind turbine blades. It is a cost-effective system with good thermal and mechanical properties.
• Spabond 340LV HT (v1)
  Spabond 340LV is a high performance adhesive for bonding large wind turbine blades. It is a cost-effective system with 10% lower density than competitive glass filled adhesives and high fatigue/crack resistance.
• SparPreg™ (UD Prepreg for SPRINT® – quality Blade Spars and Roots) v5
  SparPreg™ is a unique product range provides technically and commercially competitive engineering materials, ideal for use either solely, or in conjunction with other Gurit products from within the range.
• Velinox™ 100 - Novel Prepreg Resin Storable at +35°C (v1)
  Velinox™ 100 is a new resin system, developed by Gurit as a next generation resin platform to enhance our current WE Prepreg and SparPreg™ products. Velinox™ 100 is ideally suited to benefit the cure of thick sections, such as wind turbine blade spars and roots
• WE91-1 Higher Tack Glass Prepreg (v7)
  The WE91 series is part of the WE and WT range of prepreg, and SPRINT® products. There are two tack variants of the WE91 resin matrix; WE91-1 and WE91-2. This datasheet details WE91-1, the higher tack variant.
• WE91-2 - Prepreg (v3)
  The WE91 series is part of the WE and WT range of prepreg, and SPRINT® products. This unique product range is ideal for use either solely, or in conjunction with other Gurit products from within the range.
• WT93 SPRINT® (v4)
  WT93 SPRINT® is part of the WE and WT range of prepreg, and SPRINT® products.